LQ4 vs LQ9: The 6.0L Truck Engine Guide for Swaps and Builds
When someone calls us looking for a "6.0 LS," they almost always mean an LQ4 or an LQ9. These iron-block Vortec 6000 engines came out of GM trucks and SUVs by the hundreds of thousands, and they're the go-to choice for budget swaps, tow rigs, and turbo builds.
They look nearly identical on the stand. Here's what actually separates them and how to decide which one you want.
What the LQ4 and LQ9 have in common
Both are Gen III 6.0L (364 ci) V8s with a cast-iron block, a 4.00-inch bore, and a 3.622-inch stroke. Both use cathedral-port heads (the 317 casting is the common one) and the 24x crank reluctor, so they share engine management with other Gen III LS engines. The iron block is heavier than an aluminum LS, but it's also stronger, which is why builders love it for boost.
The real differences
| LQ4 | LQ9 | |
|---|---|---|
| Pistons | Dished | Flat-top |
| Compression | About 9.4:1 | About 10.1:1 |
| Factory power | ~300–325 hp | ~345 hp |
| Common donors | Silverado/Sierra 2500 and 3500, Suburban and Yukon XL 2500, Express/Savana vans, 2003–2007 Hummer H2 | Escalade, Yukon Denali, Silverado SS, some Sierra Denali and high-output trucks |
| Availability | Very common | Less common, usually costs more |
Ratings and applications vary by model year. Confirm your donor with the VIN's engine code.
The piston is the key. The LQ4's dished pistons lower compression, which makes it very forgiving under boost and on lower-octane fuel. The LQ9's flat-top pistons raise compression, which means more power naturally aspirated but less margin for big boost on pump gas.
Which one should you buy?
- Turbo or supercharger build: the LQ4 is the classic choice. Lower compression and plentiful supply make it the budget boost engine.
- Naturally aspirated performance: the LQ9's higher compression gives you more power without a blower.
- Truck repair or tow rig: match what came in the truck. An LQ4 is the easiest replacement for most HD trucks and vans.
- Tight budget: LQ4. There are simply more of them.
How to tell an LQ4 from an LQ9
- Check the donor VIN. The eighth digit of the vehicle VIN identifies the factory engine. That's the most reliable method when the engine comes with donor information, which ours do.
- Look at the pistons. Pull a head or use a borescope through a spark plug hole. Dished means LQ4, flat-top means LQ9.
- Don't rely on appearance alone. Covers, intakes, and accessories can be swapped between engines.
Frequently asked questions
Is the LQ9 better than the LQ4?
For naturally aspirated power, yes, thanks to higher compression. For boosted builds, many builders prefer the LQ4's lower compression. "Better" depends on your plan.
Do the LQ4 and LQ9 use the same heads?
Both commonly use the 317 cathedral-port head. The main difference is the pistons and resulting compression.
Can I swap an LQ4 into a car?
Yes. It's the same basic LS footprint. It's heavier than an aluminum LS, and you'll need the right oil pan, accessory drive, and mounts for your chassis.
What years did the Hummer H2 use the LQ4?
2003–2007. Later H2s moved to the 6.2L.
Weighing a 6.0L against a car engine? See our LS1 vs LS6 vs LS3 comparison.
Shop 6.0L LQ4 dropouts and parts
Tested engines with mileage listed, plus harnesses, ECUs, intakes, and heads.